LCD Display Flexible Flat Cable

Say LCD Display Flexible Flat Cable et sakey a flat cable assembly ya mangikokonekta ed saray LCD panel tan display modules ya walaan na driver boards, control PCBs, tan arum niran electronic interface. Saray konpigurasyon et mansaklaw na 0.3-1.0 mm ya estandarten tono, 4-100+ ya konduktor, nipasal ya karukey na kable, direksion na kontak, pampabiskeg, tan pantutunosan na ZIF/LIF connector.

Bilang na Tono tan Konduktor
Say bilang na pitch tan conductor et mipara ed contact spacing tan circuit count na target ya LCD connector.

Orientation ed Kontak
Wala ray parehon-side tan kabaliktaran-contact, kaiba lay Type A tan Type D ya configuration. Say orientation na contact et nibaga unong ed posisyon na konektor ed sampot na LCD tan PCB.

ZIF / LIF Interface
Say FFC contact section et aka-configure parad ZIF o LIF connector interfaces, ya saray sukat na contact tan saray kakaukolanen ed pangisulong et akumpirma sumpad nibaga ya connector.

Panagpabiskeg na Kontak
Nayarin idagdag so PET o PI stiffeners ed lugar ya akatongtong. Say materyales tan sukat na stiffener et nibaga unong ed istruktura na konektor tan saray kakaukolanen ed pangiloob.
 

Karukey na Kable
Say karukey na kable et mipara ed distansya na LCD module, driver board, tan control PCB. Say karukey et nayarin ipaliwawa unong ed walan pasen ya pantitiponan tan say dalan na rota.

Layout na Konduktor
Say inkauksoy na konduktor et ontutumbok ed nakaukolan a bilang na sirkito tan say inkauksoy na konektor, ya pansiansiaen so pattern na kontak na kable ya aka-align ed display-side tan board-side interfaces.

Internal Routing
Say patatdang ya profile et mamaabuloy ed kable ya makadalan ed limitadon loob na espasyo ed loob na display assembly. Say karukey na kable, say posisyon na kurko, tan say orientation na contact et nayarin i-coordinate ed dalan na pangi-install.

Dynamic Bending
Parad saray asemblea ya mankaukolan na paulit-ulit ya galaw o pananguman, say nibaga ya konstruksion et onsusuportad 10,000+ bending cycles. Saray kakaukolanen ed panag-bending et nepeg ya kumpirmaen a kaiba so geometry na instalasyon tan saray kondisyon na panag-operate.

Drawing / Sample Input
Saray drowing na kustomer, saray teknikal ya detalye, odino saray wala lan sample na FFC et nayarin iter bilang basiyan na panagpaalagey.

Repaso ed Inhenyeriya
Say pitch, bilang na pin, karukey na kable, orientation na contact, interface na connector, materyal, tan arum niran nakaukolan ya detalye et narepaso parad posibilidad tan say pampili na materyales antis ya man-sampling.

Prototype Approval
Saray sample na prototype et na-check parad sukat, contact configuration, tan electrical performance. Say naaprobaan ya sample tan saray detalye et usaren parad produksyon.
 

Dimensional Inspection
Say pitch, kalapar na konduktor, karukey na kable, sukat na kontak, tan amin ya sukat et na-check sumpad saray inaprobaan ya detalye.

Pansukimat ed Kuryenti
Say 100% ya panagsukimat et mansaklaw ed pantultuloy, resistensya na konduktor, resistensya na insulasyon, tan biskeg na dielectric.

Inspeksyon ed Kontak
Say direksion na kontak, say akabantag ya lugar na kontak, say sukat na kontak, tan say posisyon na terminal et inspeksionen sumpad naaprobaan ya configuration.

Kaunoran ya Inspeksyon
Saray asumpal ya kable et kaukolan ya nengnengen, na-verify so sukat da, tan na-check ed kuryente antis ya ipawit.

Inaprobaan ya Reperensya ed Produksyon
Saray naaprobaan ya sample, drowing, tan pinal iran detalye et pansiansiaen bilang reperensya ed produksyon parad ontumbok iran order na parehon LCD FFC configuration.

Uliten so Pankakasakey na Order
Say pitch, bilang na konduktor, karukey na kable, orientation na contact, reinforcement, insulation, tan configuration na connector et ontutumbok ed naaprobaan ya detalye parad paulit-ulit ya produksyon.